This is the default partition map for all external drives. If you are formatting this drive for use as a drive on a PPC based Mac select “Apple Partition Map” and click Ok. The next step is to choose the partition map you want to use.2. Once you are on the “Partition” click “Options” at the bottom. Once you have opened “Disk Utility”, click on your new drive on the left hand side and then click on the “Partition” tab on the right. Here is an instruction guide for the formatting process using Apple’s Disk Utility (included with OSX, located in Applications > Utilities folder)1. Click on your old hard drive to start the booting process, and your Mac will start up normally after that.įormatting Your New Hard DriveFormatting the new hard drive will be the next step you will need to take to add a volume to the drive. This will give you a boot menu that looks like the picture to the left. If you have an external enclosure for the old hard drive, you will plug that in via Firewire or USB, (Note: USB is only a bootable option on Intel Macs) then turn on your computer while holding down the Option key on your keyboard.
Destination SSD smaller than source HDD, but data on source HDD is less than the usable capacity on the SSD. Destination SSD equal or larger than source HDD:ģ.a.You first must clean up space on the source HDD till you meet condition 2 or 3 and then follow the relevant instructions.Destination SSD smaller than source HDD, and data on source HDD is equal or more than the usable capacity on the SSD.You will now follow the instructions based on one of the following situations: Fill in your e-mail address, click on get code, and copy and paste the code you receive via e-mail.Read and accept the License Agreement, select next.Click “Next” to extract the setup files and begin installing.Windows will ask whether or not you want to allow Macrium Reflect 7 to make changes – select “Yes”.Select “Download” – the Macrium Reflect installer will then download. Once ReflectDLHF.exe has downloaded, install it, by running ReflectDLHF.exe.You will now have a new drive volume that was created on the new SSD.ĭownload and Install Cloning Software: – note this is freeware and intended for your private use:.VERY IMPORTANT: Note the drive letter i.e.Right click on the unallocated disk space.You will now see a disk with unallocated disk space.Step3: Slide into drive enclosure till closed and connect USB cable to the enclosure and to the laptop’s USB port.You do not need to fasten the screws at this point as we will remove the SSD again.Step 2: Align and connect SSD to the SATA port of the drive enclosure.Step 1: Separate the USB side from the drive enclosure.The drive enclosure comes with the following components:.Installation of SSD into Drive Enclosure: Errors were found and NOT fixed – Please proceed with extreme caution, it is likely that the clone process might fail, and data could be lost.“Errors were found and fixed” – You are good to start the cloning process.No Errors Found – You are good to start the cloning process.Step 5: In “Error checking” click on “Check”.Step 2: Right click on the drive you want to check (typically C drive).Please conduct the following checks before continuing with the process: It is your responsibility to select the correct size SSD. SSD drive that has at least 100%-120% more capacity than the capacity that is in use on your HDD – supplied in the bundle.Philips small tip screwdriver – supplied in the bundle.External Hard Disk Bay for 2.5” drives – supplied in the bundle.
More details and links to resources will be provided as we work through the detailed steps: Windows Cloning guide:īelow is a high-level list of what you need. It is recommended that the SSD’s capacity is at least 20% bigger than the capacity of data you currently have on all your partitions.Įxternal SSD install 1.Your laptop uses a 2.5” SATA Hard Disk Drive.You can replace a hard drive in a laptop and have all the tools required.You a basic understanding of installation of applications and opening and closing laptops.Backing up data always remains your responsibility and will not be discussed in detail on this page. This page is intended to help you clone your old laptop hard disk drive (HDD) to a new solid-state drive (SSD).īefore we go further it is very important to note that you should backup your data before attempting to clone your hard drive.